配置RRPP 多實例單環

1、以下是配置實例UPE A 的配置文件#sysname UPEA#vlan batch 5 to 6 10 to 11 100 to 300#rrpp enable /使能RRPP協議#stp region-configuration /創建實例instance 1 vlan 5 6 100 to 200 /實例1映射VLAN 5,6,100-200 instance 2 vlan 10 11 201 to 300active region-configuration /激活MSTP域的配置#rrpp domain 1 /創建并進入RRPP域 1control-vlan 5 /控制VLAN 5p

2、rotected-vlan reference-instance 1 /域1環1保護的VLAN為實例1映射之VLANring 1 node-mode transit primary-port GigabitEthernet 1/0/0 secondary-port GigabitEthernet 2/0/0 level 0 /設置為域1環1傳輸節點，主口為G1/0/0,從口為2/0/0ring 1 enable /使能域1環1rrpp domain 2 /創建并進入RRPP域 2control-vlan 10 /控制VLAN 10protected-vlan reference-instanc

3、e 2 /域2環1保護VLAN為實例2映射VLANring 1 node-mode transit primary-port GigabitEthernet 1/0/0 secondary-port GigabitEthernet 2/0/0 level 0 /設置為域2環1傳輸節點，主口為G1/0/0,從口為2/0/0ring 1 enable /使能域2環1#interface GigabitEthernet1/0/0port link-type trunkport trunk allow-pass vlan 5 to 6 10 to 11 100 to 300stp disable /去

4、使能端口上的STP 功能#interface GigabitEthernet2/0/0port link-type trunkport trunk allow-pass vlan 5 to 6 10 to 11 100 to 300stp disable#returnUPE B 的配置文件#sysname UPEB#vlan batch 5 to 6 10 to 11 100 to 300#rrpp enable#stp region-configurationinstance 1 vlan 5 6 100 to 200instance 2 vlan 10 11 201 to 300activ

5、e region-configuration#rrpp domain 1control-vlan 5protected-vlan reference-instance 1ring 1 node-mode transit primary-port GigabitEthernet 1/0/0 secondary-port GigabitEthernet 2/0/0 level 0ring 1 enablerrpp domain 2control-vlan 10protected-vlan reference-instance 2ring 1 node-mode transit primary-po

6、rt GigabitEthernet 1/0/0 secondary-port GigabitEthernet 2/0/0 level 0ring 1 enable#interface GigabitEthernet1/0/0port link-type trunkport trunk allow-pass vlan 5 to 6 10 to 11 100 to 300stp disable#interface GigabitEthernet2/0/0port link-type trunkport trunk allow-pass vlan 5 to 6 10 to 11 100 to 30

7、0stp disable#returnUPE C 的配置文件#sysname UPEC#vlan batch 5 to 6 10 to 11 100 to 300#rrpp enable#stp region-configurationinstance 1 vlan 5 6 100 to 200instance 2 vlan 10 11 201 to 300active region-configuration#rrpp domain 1control-vlan 5protected-vlan reference-instance 1ring 1 node-mode transit prima

8、ry-port GigabitEthernet 1/0/0 secondary-port GigabitEthernet 2/0/0 level 0ring 1 enablerrpp domain 2control-vlan 10protected-vlan reference-instance 2ring 1 node-mode transit primary-port GigabitEthernet 1/0/0 secondary-port GigabitEthernet 2/0/0 level 0ring 1 enable#interface GigabitEthernet1/0/0po

9、rt link-type trunkport trunk allow-pass vlan 5 to 6 10 to 11 100 to 300stp disable#interface GigabitEthernet2/0/0port link-type trunkport trunk allow-pass vlan 5 to 6 10 to 11 100 to 300stp disable#ReturnPE-AGG 的配置文件#sysname PE-AGG#vlan batch 5 to 6 10 to 11 100 to 300#rrpp enable#stp region-configu

10、rationinstance 1 vlan 5 6 100 to 200instance 2 vlan 10 11 201 to 300active region-configuration#rrpp domain 1control-vlan 5protected-vlan reference-instance 1ring 1 node-mode master primary-port GigabitEthernet 1/0/0 secondary-port GigabitEthernet 2/0/0 level 0 /設置為域1環1主節點，主口為G1/0/0,副口為2/0/0ring 1 e

11、nablerrpp domain 2control-vlan 10protected-vlan reference-instance 2ring 1 node-mode master primary-port GigabitEthernet 2/0/0 secondary-port GigabitEthernet 1/0/0 level 0 /設置為域2環1主節點，主口為G2/0/0,副口為1/0/0ring 1 enable#interface GigabitEthernet1/0/0port link-type trunkport trunk allow-pass vlan 5 to 6

12、10 to 11 100 to 300stp disable#interface GigabitEthernet2/0/0port link-type trunkport trunk allow-pass vlan 5 to 6 10 to 11 100 to 300stp disable#return執行display stp region-configuration 命令，可以查看實例與VLAN 之間的映射關系。例如：<Quidway> display stp region-configurationOper configurationFormat selector :0Reg

13、ion name :00e0fc010203Revision level :0Instance Vlans Mapped0 3 to 9, 12 to 99, 301 to 40941 1 to 2, 100 to 2002 10 to 11, 201 to 300l 在UPE A 上執行display rrpp brief 命令，查看結果如下：<UPEA> display rrpp briefAbbreviations for Switch Node Mode :M - Master , T - Transit , E - Edge , A - Assistant-EdgeRRP

14、P Protocol Status: EnableRRPP Working Mode: HWRRPP Linkup Delay Timer: 0 sec (0 sec default).Number of RRPP Domains: 2Domain Index : 1Control VLAN : major 5 sub 6Protected VLAN : Reference Instance 1Hello Timer : 1 sec(default is 1 sec) Fail Timer : 3 sec(default is 3 sec)Ring Ring Node Primary Seco

15、ndary/Edge IsID Level Mode Port Port Enabled-1 0 T GigabitEthernet1/0/0 GigabitEthernet2/0/0 YesDomain Index : 2Control VLAN : major 10 sub 11Protected VLAN : Reference Instance 2Hello Timer : 1 sec(default is 1 sec) Fail Timer : 3 sec(default is 3 sec)Ring Ring Node Primary Secondary/Edge IsID Leve

16、l Mode Port Port Enabled-1 0 T GigabitEthernet1/0/0 GigabitEthernet2/0/0 Yes在PE-AGG 上執行display rrpp brief 命令，查看結果如：<PE-AGG> display rrpp briefAbbreviations for Switch Node Mode :M - Master , T - Transit , E - Edge , A - Assistant-EdgeRRPP Protocol Status: EnableRRPP Working Mode: HWRRPP Linkup

17、 Delay Timer: 0 sec (0 sec default).Number of RRPP Domains: 2Domain Index : 1Control VLAN : major 5 sub 6Protected VLAN : Reference Instance 1Hello Timer : 1 sec(default is 1 sec) Fail Timer : 3 sec(default is 3 sec)Ring Ring Node Primary/Common Secondary/Edge IsID Level Mode Port Port Enabled-1 0 M

18、 GigabitEthernet1/0/0 GigabitEthernet2/0/0 YesDomain Index : 2Control VLAN : major 10 sub 11Protected VLAN: Reference Instance 2Hello Timer : 1 sec(default is 1 sec) Fail Timer : 3 sec(default is 3 sec)Ring Ring Node Primary/Common Secondary/Edge IsID Level Mode Port Port Enabled-1 0 M GigabitEthern

19、et2/0/0 GigabitEthernet1/0/0 Yes詳細說明：控制VLAN在RRPP 域中，控制VLAN 用來傳遞RRPP 協議報文。控制VLAN 中只能包含RRPP 端口。每個RRPP 域配有兩個控制VLAN，分別為主控制VLAN 和子控制VLAN。配置時只需要指定主控制VLAN，而把比主控制VLAN ID 值大1 的VLAN 作為子控制VLAN。與控制VLAN 相對，數據VLAN 用來傳輸數據報文。數據VLAN 中可以包含RRPP端口，也可以包含非RRPP 端口第一步 ：創建實例 在需要加入RRPP多實例域的交換機上進行配置*stp region-configuration 進

20、入MSTP域視圖*instance instance-id vlan vlan-id to vlan-id &<1-10>，配置實例和VLAN的映射關系 默認 實例 映射的VLAN 0 1 to 4094 一個域中最多可創建49 個實例，其中Instance 0 為缺省配置，不需要?jiǎng)?chuàng)建。 缺省情況下，所有的VLAN 都映射到Instance 0第二步：配置RRPP環上的接口 在需要加入RRPP 環的端口上進行以下配置* port trunk all vlan xxxx 設置數據VLAN（即普通數據VLAN） 控制VLAN 由RRPP 域視圖下的control-vlan 命令

21、指定，并配置了ring node-mode 命令后，自動成為RRPP環上各端口允許通過的VLAN。因此，本步驟中僅需指定數據VLAN 即可*stp disable，去使能端口上的STP 功能。 缺省情況下，設備所有端口上都使能了STP 協議。在創建RRPP環前，需要先去使能即 將加入RRPP環中的端口的STP 功能第三步：創建RRPP域 在RRPP 域內每臺交換機上進行如下配置*rrpp domain domain-id 創建RRPP域 創建RRPP 域時要指定域的ID，如果該域已存在則直接進入域視圖。 第四步：配置保護VLAN 在RRPP域內每臺交換機上進行如下配置*rrpp domain

22、domain-id 進入RRPP 域視圖。*protected-vlan reference-instance instance-id1 to instance-id2 &<1-10> |all ，配置RRPP 域的保護VLAN 列表。 引用最上面實例名映射的VLAN RRPP 端口允許通過的VLAN 都應該配置為保護VLAN，包括數據VLAN 和控制VLAN。第五步：創建控制VLAN 在RRPP 域內每臺交換機上進行如下配置*rrpp domain domain-id，進入域視圖*control-vlan vlan-id，創建控制VLAN 控制VLAN 創建后不能直接修改

23、，只能通過先刪除域，然后再重新配置的方式修改。子控制VLAN 也在刪除域時被連帶刪除第六步：創建RRPP環 在RRPP 域內每臺交換機上進行如下配置*rrpp domain domain-id，進入域視圖。*ring ring-id node-mode master |transit primary-port interface-type interfacenumber secondary-port interface-type interface-number level level-value master 主節點 transit 傳輸節點 primary-port 指定擔當主端口 secondary-port 擔當副端口 環級別為0 表示主環，級別為1 表示子環 邊緣節點和輔助邊緣節點所在的環級別系統自動設置為1，不