華為交換機bootromFTP方式升級版本.doc

以MSR5040路由器、FTP/TFTP服務器主機直連為例操作步驟：1 路由器上電自檢出現如下的信息：InitDDR.system start booting.Version 2.11Press CTRL+D to stop auto-bootBooting Normal Extended BootRomDecompressing.done!Ensure the baudrate is set to 9600bps!Starting at 0xa00000. * * * * H3C MSR50-40 BOOTROM, Version 2.13 * * * * Copyright(c) 2004-2007 Hangzhou H3C Technologies Co., Ltd. Compiled date: Jul 31 2007, 14:05:28 CPU type : MPC8541 CPU L1 Cache : 32KB CPU L2 Cache : 256KB CPU Clock Speed : 833MHz Memory Type : DDR SDRAM Memory Size : 512MB Memory Speed : 333MHz BootRom Size : 4096KB CPLD Version is 2.00 HardWare Version is 3.00CF Card is Inserted, now is mounting.cf:/ - Volume is OK Mount CF Card OK!CF Card Size:256MBPress Ctrl+B to enter extended boot menu.此時鍵入，系統將進入BOOTROM菜單。& 說明：必須在出現“Press Ctrl-B to enter Boot Menu.”的3秒鐘之內，鍵入，系統方可進入BOOTROM菜單；否則系統將進入程序解壓過程。若進入程序解壓過程后再希望進入BOOTROM菜單，則需要重新啟動路由器。2進入Bootrom界面用戶鍵入后，系統提示：Please input Bootrom password:此時需要用戶要輸入BootROM口令（路由器出廠時缺省沒有BootROM口令，直接回車即可）。若用戶已經修改過BootROM口令，應該輸入正確的口令，若三次口令驗證未通過，則系統中止。3. 選擇以太網口，進行配置升級當用戶輸入了正確的BootROM口令，系統將出現如下提示信息：=| Boot From CF Card | Enter Serial SubMenu | Enter Ethernet SubMenu | File Control | Modify Bootrom Password | Ignore System Configuration | Boot Rom Operation Menu | Clear Super Password | Device Operation | Reboot |=Enter your choice(1-a):3 選擇3進入串口子菜單: Enter Ethernet SubMenu=|Note:the operating device is CF Card | Download Application Program To SDRAM And Run | Update Main Application File | Update Backup Application File | Update Secure Application File | Change Ethernet Parameter | Exit To Main Menu | |=Enter your choice(1-6):5選擇5對以太網口進行調整4對FTP參數進行設置以太網口配置菜單：Note: Two protocols for download, tftp & ftp. You can modify the flags following the menu except the boot device. tftp-0x80, ftp-0x0. = clear field; - = go to previous field; Ctrl+D = quitboot device:motfcc1網絡下載設備名字，無需更改processor number:0處理器數，無需更改host name:host主機名字，無需更改file name:MSR50-CMW520-R1508P02-SI.BIN與服務器文件一致inet on ethernet (e) :根據實際組網進行設置inet on backplane (b):無需設置host inet (h) :FTP或TFTP服務器的ip地址gateway inet (g) :網關ip地址，根據實際情況設置user (u) :bbxz下載用戶名ftp password (pw) (blank = use rsh): 123456下載密碼flags (f) :0x0下載標識，F(xiàn)TP為0x0，TFTP為0x80target name (tn) :設置保存在Flas中的目標文件的名稱，無需設置startup script (s) :無需設置other (o) :無需設置4下載文件選擇2將指定文件下載到CF卡中作為主啟動文件=|Note:the operating device is CF Card | Download Application Program To SDRAM And Run | Update Main Application File | Update Backup Application File | Update Secure Application File | Change Ethernet Parameter | Exit To Main Menu | |=Enter your choice(1-6):2boot device : mottsecunit number : 0 processor number : 0 host name : hostfile name : MSR50-CMW520-R1508P02-SI.BINinet on ethernet (e) : host inet (h) : user (u) : guestftp password (pw) : 123456flags (f) : 0x0 Attached TCP/IP interface to mottsec0.Warning: no netmask specified.Attaching network interface lo0. done.Loading.Done!18339940 bytes downloaded.Input the File Name:MSR50-CMW520-R1508P02-SI.BIN/Updating File cf:/msr50-cmw520-r1508p02-si.bin.Update Success!5重啟升級（版本更換）下載完畢后重啟路由器完成版本升級（更換）操作?！咎崾尽?、MSR 20系列路由器只能使用Ethernet0/0端口，MSR 30及MSR 50系列路由器只能使用GigabitEthernet0/0端口。2、Boo