機組聯鎖設置參考標準

1、 機組儀表聯鎖設置的相關標準一、公司儀表聯鎖保護系統管理制度(附件1：) 大機組聯鎖設置原則(一) 大機組軸瓦溫度聯鎖：止推瓦溫度測量要求每個面設三個測溫點，采用三取二聯鎖。如果只能安裝二個測溫點，則采用二取二聯鎖，但必須設置溫度報警。支撐瓦溫度聯鎖，機組中無軸系振動聯鎖保護信號的，設軸瓦溫度聯鎖。在機組中已配置軸系振動聯鎖保護的，不設支撐瓦溫度聯鎖。但必須設置支撐瓦溫度高報警信號。(二) 大機組油壓低低聯鎖：潤滑油壓需采用三取二聯鎖。為了解決油泵切換過程中油壓瞬變問題，潤滑油壓低低聯鎖邏輯中加3S延時（即潤滑油壓低低信號持續時間大于3S后才啟動聯鎖）。汽輪機速關油壓、動力油壓低低聯鎖：在機組

2、安全保護上，速關油壓、動力油壓低低有機械保護，無特別要求不設聯鎖。潤滑油壓變送器的取壓口須在潤滑油總管的末端。(三) 重要機組透平轉速高聯鎖設置三個獨立的轉速測量，采取三取二聯鎖。(四) 重要大機組都必須設置軸振動、軸位移聯鎖。同一斷面X、Y方向軸振動聯鎖采取二取二聯鎖。機組軸位移要求同一端安裝三個位移傳感器，采取三取二聯鎖。如果只安裝二個位移傳感器的采取二取二聯鎖，必須設置二個位移傳感器測量偏差報警。(五) 對大機組電機三組定子溫度設置聯鎖，但須采取三取二方式，設置溫度報警。(六) 機組停機后的工藝聯鎖。考慮到現場等因素，應以機組實際運行狀態作為工藝聯鎖啟動條件。汽輪機機組用速關油壓低低（三

3、取二）做機組、工藝聯鎖觸發信號之一，聯鎖值除特殊要求外取0.4Mpa。開機時速關油壓低低切除，開機正常后即投用。電機機組用電機運行狀態（來自電氣）做工藝聯鎖觸發信號之一。以上信號同時輸出到報警燈屏指示臺，指示機組停機。儀表： 機械： 電氣： 機動處長：二、石油化工安全儀表系統設計規范三、API670標準Machinery ProtectionSystemsAPI STANDARD 670 FOURTH EDITION, DECEMBER 20005.4.2.4 The radial shaft vibration shutdown system shall be field changeabl

4、e so that one (single logic) or both (dual voting logic see note) transducer signals must reach or violate the setpoint to activate a shutdown (danger) relay. Dual voting (two-out-of-two) logic shall be standard. Note: In a dual voting logic system, although each channel may have reached or violated

5、 its respective shutdown (danger) setpoints at different times, both channels must be jointly and continuously at or above the shutdown (danger) setpoint for the time delay specified in=5.4.3.4 The axial position shutdown system shall be field changeable so that one (single logic) or both (dual voti

6、ng logic, see note following) transducer signals must reach or violate the shutdown (danger) setpoint to actuate the shutdown (danger) relay. Dual voting (two out of two) logic shall be standard.Note: In an axial position dual voting logic system, although each channel may have reached or violated i

7、ts respective preset shutdown (danger) setpoints at different times, both channels must jointly and continuously be at or above the shutdown (danger) setpoints for the time delay specified in 5.4.1.5.d before the shutdown (danger) relay activates. In the event of the failure of a single transducer o

8、r circuit, only the circuit-fault alarm and the alarm (alert) will activate that is, the shutdown (danger) relay will not activate. The shutdown (danger) relay will activate when any of the following conditions occur: a. Both axial position transducers or circuits fail. b. Either channel has failed, and the other channel has violated the shutdown (danger) setpoint. c. Both channels jointly violate the shutdown (danger) setpoint.5.4.1.5d. With exception of electronic overspeed detection, fixed time delays for shutdown (danger) relay activation t