全志電池參數配置說明.doc

1 全志關于PMU電源配置的說明文檔1.1 pmu_parapmu_used=xx 1Pmu使能標志(xx=1 or 0)，0：不使用，1：使用1pmu_twi_addr=xx 0x34Pmu 設備地址pmu_twi_id=xx 0Pmu掛載的i2c控制器號，0：twi0，1：twi1，2：twi2pmu_irq_id=xx 0Pmu 中斷號，0：NMI，1：1號中斷2：2號中斷pmu_battery_rdc=xx 150電池內阻，m，根據實際測試填寫pmu_battery_cap=xx 4000電池容量，mAh，根據實際測試填寫pmu_init_chgcur=xx 300設置開機充電電流，mA，300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800pmu_earlysuspend_chgcur=xx 500設置關屏充電電流，mA，300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800pmu_suspend_chgcur=xx 1000設置休眠充電電流，mA，300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800pmu_resume_chgcur=xx 300設置喚醒充電電流，mA，300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800pmu_shutdown_chgcur=xx 1300設置關機充電電流，mA300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800pmu_init_chgvol=xx 4200設置充電目標電壓，mV，4100/4150/4200/4360pmu_init_chgend_rate=xx 15設置結束充電電流的比率，%，10，15pmu_init_chg_enabled=xx 1設置充電功能，0：關閉，1：打開pmu_init_adc_freq=xx 100設置adc采樣率，Hz，25/50/100/200pmu_init_adc_freqc=xx 100設置庫侖計采樣率，Hz，25/50/100/200pmu_init_chg_pretime=xx 50設置預充電超時時間，min，40/50/60/70pmu_init_chg_csttime=xx 720設置恒流充電超時時間，min，360/480/600/720pmu_bat_para1=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para2=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para3=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para4=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para5=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para6=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para7=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para8=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para9=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para10=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para11=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para12=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para13=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para14=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para15=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔pmu_bat_para16=xx設置空載電池電壓對應的百分比，%，具體請看電池參數測試操作指南文檔，建議此處固定為100pmu_usbvol_limit=xx 1設置usb限壓功能，0：關閉，1：打開pmu_usbvol=xx 4400設置usb限壓電壓，mV，4000/4100/4200/4300/4400/4500/4600/4700pmu_usbcur_limit=xx 0設置usb限流功能，0：關閉，1：打開pmu_usbcur=xx 500設置usb限流電流，mA，100/500/900pmu_pwroff_vol=xx 3300設置啟動時的硬件保護電壓，mV，2600/2700/2800/2900/3000/3100/3200/3300pmu_pwron_vol=xx 2900設置開機狀態下的硬件保護電壓，mV，2600/2700/2800/2900/3000/3100/3200/3300pmu_pekoff_time=xx 6000設置硬件關機時長，ms，4000/6000/8000/10000pmu_pekoff_en=xx 1設置硬件關機功能，0：關閉，1：打開pmu_peklong_time=xx 1500設置長按鍵中斷時間，ms，1000/1500/2000/2500pmu_pekon_time=xx 2000設置開機時間，ms，128/1000/2000/3000pmu_pwrok_time=xx 64設置電源啟動完成后pwrok信號延時，ms，8/64pmu_pwrnoe_time=xx 2000設置n_oe由低變高后關機延遲時間，ms，128/1000/2000/3000pmu_intotp_en=xx 1設置過溫關機功能，0：關閉，1：打開pmu_used2=xx專門為佳的美案子做的一個設置，配合pmu_adpdet pmu_shutdown_chgcur2，打開1，關閉0pmu_adpdet=xx佳的美案子的設置，火牛探測口設置，具體參看上面gpio的配置pmu_init_chgcur2=xx佳的美案子的設置，插入火牛時，開機充電電流設置，同pmu_init_chgcurpmu_earlysuspend_chgcur2=xx佳的美案子的設置，插入火牛時，關屏充電電流設置，同pmu_earlysuspend_chgcurpmu_suspend_chgcur2=xx佳的美案子的設置，插入火牛時，休眠充電電流設置，同pmu_suspend_chgcurpmu_resume_chgcur2=xx佳的美案子的設置，插入火牛時，喚醒充電電流設置，同pmu_resume_chgcurpmu_shutdown_chgcur2=xx佳的美案子的設置，插入火牛時，關機充電電流設置，同pmu_shutdown_chgcurpmu_suspendpwroff_vol=xx 3400休眠關機電壓設置，mV，28674200，6mV一檔pmu_batdeten=xx 1電池探測功能設置，0：關閉，1：打開注意：pmu_used2 pmu_shutdown_chgcur2之間的參數是為佳的美案子專門做的接口，對其他案子可以刪掉。配置舉例：pmu_used= 1pmu_twi_addr= 0x34pmu_twi_id= 0pmu_irq_id= 0pmu_battery_rdc= 200pmu_battery_cap= 2600pmu_init_chgcur= 300pmu_earlysuspend_chgcur = 600pmu_suspend_chgcur= 1000pmu_resume_chgcur= 300pmu_shutdown_chgcur= 1000pmu_init_chgvol= 4200pmu_init_chgend_rate= 15pmu_init_chg_enabled= 1pmu_init_adc_freq= 100pmu_init_adc_freqc= 100pmu_init_chg_pretime= 50pmu_init_chg_csttime= 720pmu_bat_para1 = 0pmu_bat_para2 = 0pmu_bat_para3 = 1pmu_bat_para4 = 5pmu_bat_para5 = 7pmu_bat_para6 = 13pmu_bat_para7 = 16pmu_bat_para8 = 26pmu_bat_para9 = 36pmu_bat_para10 = 46pmu_bat_para11 = 53pmu_bat_para12 = 61pmu_bat_para13 = 73pmu_bat_para14 = 84pmu_bat_para15 = 92pmu_bat_para16 = 100pmu_usbvol_limit= 1pmu_usbvol= 4400pmu_usbcur_limit= 0pmu_usbcur= 900pmu_pwroff_vol= 3300pmu_pwron_vol= 2900pmu_pekoff_time= 6000 pmu_pekoff_en= 1pmu_peklong_time= 1500pmu_pekon_time= 1000pmu_pwrok_time= 64pmu_pwrnoe_time= 2000pmu_intotp_en= 1pmu_used2 = 0pmu_adpdet = port:PH02pmu_init_chgcur2 = 400pmu_earlysuspend_chgcur2 = 600pmu_suspend_chgcur2 = 1200pmu_resume_chgcur2 = 400pmu_shutdown_chgcur2 = 1200pmu_suspendpwroff_vol = 3500pmu_batdeten = 1我們現在用的配置pmu_parapmu_used = 1pmu_twi_addr = 0x34pmu_twi_id = 0pmu_irq_id = 0pmu_battery_rdc = 150pmu_battery_cap = 4000pmu_init_chgcur = 300pmu_earlysuspend_chgcur = 600pmu_suspend_chgcur = 1000pmu_resume_chgcur = 300pmu_shutdown_chgcur = 1000pmu_init_chgvol = 4200pmu_init_chgend_rate = 15pmu_init_chg_enabled = 1pmu_init_adc_freq = 100pmu_init_adc_freqc = 100pmu_init_chg_pretime = 50pmu_init_chg_csttime = 720pmu_bat_para1 = 0pmu_bat_para2 = 0pmu_bat_para3 = 0pmu_bat_para4 = 0pmu_bat_para5 = 5pmu_bat_para6 = 8pmu_bat_para7 = 11pmu_bat_para8 = 22pmu_bat_para9 = 33pmu_bat_para10 = 43pmu_bat_para11 = 50pmu_bat_para12 = 59pmu_bat_para13 = 71pmu_bat_para14 = 83pmu_bat_para15 = 92pmu_bat_para16 = 100pmu_usbvol_limit = 1pmu_usbcur_limit = 0pmu_usbvol = 4000pmu_usbcur = 0pmu_u