手機產品質量標準.doc

手機產品質量標準本產品質量標準由以下四個部分組成：第一部分：產品技術規格書（電性能部分）第二部分：產品外觀檢驗標準第三部分：產品功能檢驗標準第四部分：產品可靠性檢驗標準第一部分：產品技術規格書（電性能部分）1 GSM 900MHz 電性能測試標準GSM900射 頻 載 波 功 率信道功率等級Peak burst power （dBm）Average power （dBm）標準range標準rangeULLLULLLCH1PCL5333531333531PCL8273024273024PCL161115711157PCL1951005100CH62PCL5333531333531PCL8273024273024PCL161115711157PCL1951005100CH124PCL5333531333531PCL8273024273024PCL161115711157PCL1951005100發射功率/時間特性信道功率等級測試內容標準CH1PCL5Power time template發射功率突發脈沖在GSM規范要求的功率/時間波罩內CH62CH124相 應 誤 差信道功率等級Phase error peak（dg）Phase error RMS（dg）GBGBCH1PCL5205CH62205CH124205頻率誤差信道功率等級標準(Hz)CH1PCL590CH6290CH12490接收誤碼率信道等級標準resultCH1Ber class2150小時。白卡測試結果供參考。2通話時間測試Communication time test測試手機在通話時，電池在額定容量下維持手機通話的最長時間.The battery with rate capacity, Inspect the max time to communicate with the handset.電池在額定容量下，將手機聽筒音量開到最大，分別在移動網和聯通網，手機呼叫建立通話聯系后，至到自動關機為止。記錄各自手機的通話時間，5臺平均即為手機通話時間；要求手機關閉其它設置，網絡信號在-65-85dBm范圍內.The battery with rate capacity, the volume set the max.Mobile Card and Unicom Card division of communication. Record each set the longest commun5PCS推薦大于120分鐘（具體按產品定義）Commended more than 120 minutes (According to the product SPEC)3溫升實驗Temperature rise test驗證手機在通話過程中，手機溫度是否會升高并超過標準要求.Inspect the temperature variety of handset during communicating.最大功率發射。并工作于CH62。裝入低電電池，開機、充電狀態下將手機與模擬基站建立連接，持續通話90分鐘。持續通話中，聽筒音量開到最大，實時測量手機表面（按鍵、電池表面）、聽筒部分的溫度值；分別以90分鐘內測量到的手機表面及聽筒部分的最高溫度值為最終實驗溫度。The handsets with the max transmit power in channel 62, Low electrical voltage, power on and charge. Communicate with the2PCS通話過程中不能出現掉話現象，試驗后功能、性能正常。手機表面溫度上升不超過15，聽筒部分不能超過12.Interrupted exception is not allowed during the test. The function and performance is normal after test. The surface temperature variety is not more than 15. The receiver temperature variety is not mor環境試驗 Environment Test4高低溫貯存Hot/Cold test in storage驗證手機在高低溫環境條件下貯存的適應性Validate the capacity of the handset to be stored in low and high temperature conditions.被測樣機不包裝、不通電狀態放進具有20的試驗箱內。使試驗箱在30分鐘內溫度達到-253，溫度穩定后持續48小時,然后在30分鐘內又使溫度回到20;在30分鐘內使試驗箱內溫度達到702，溫度穩定后持續48小時，再在30分鐘內使試驗箱內溫度回復到20，放置期滿，被測樣機進行試驗后檢查。Put the unpacked and power off samples in the test box in 20 temperature.The room temperature reduce to10PCS通過基本功能、性能測試；外觀和結構正常Base function and performance test is OK; Appearance and structure are normal.5高低溫工作Hot/Cold test in operation驗證手機在高低溫環境條件下使用的適應性Validate the capacity of the handset to be operation in low and high temperature conditions.被測樣機不包裝、處于通電待機狀態，放進具有20的試驗箱內。使溫度在30分鐘內達到-203，溫度穩定后持續16時，然后在30分鐘內又使溫度回到20；再使試驗箱在30分鐘內溫度達到+552，溫度穩定后持續16小時，再在30分鐘內使試驗箱內溫度回復到20，持續期滿。立即進行被測樣機試驗后檢查。Put the unpacked and switched on samples in the test box in 20 temperature.The room temperature reduc10PCS通過基本功能、性能測試；外觀和結構正常Base function and performance test is OK; Appearance and structure are normal.6恒定濕熱Damp Heat test驗證手機在恒定濕熱環境條件下使用的適應性.Inspect the performance of the handset under high temperature and high humidity.被測樣機不包裝、處于通電待機狀態，以翻蓋打開位置放進試驗箱內。使溫度達到+402，濕度達到95%（+2%/-3%），穩定后持續96小時，持續期滿。立即進行被測樣機試驗后檢查。put the unpacked, power on and folder opened samples into the constant temperature box. When the temperature arrive retentively +402 and humidity is 95（+2%/-3%）10PCS通過基本功能、性能測試；外觀和結構正常Base function and performance test is OK; Appearance and structure are normal.7溫度沖擊實驗Thermal shock test驗證手機經受環境溫度迅速變化的能力.Inspect the performance of the handset under the vertiginous temperature.被測樣機不包裝、不帶電池狀態，以正常位置放進試驗箱內。高溫為+702，穩定溫度保持時間2h；低溫為403，穩定溫度保持時間2h；轉換時間不大于5分鐘；循環次數為12次（1個循環周期為4小時5分鐘）。循環期滿，在正常大氣條件下放置2h。放置期滿，被測樣機進行試驗后檢查。put the unpacked and power off 5pcs QC pASSED samples into the Thermal Shock Box. High temperature is 702, keep t10PCS通過基本功能、性能測試；外觀和結構正常Base function and performance test is OK; Appearance and structure are normal.8結露實驗Dew test驗證手機在結露環境下的適應性.Validate the performance of the handset under the dew environment.待機狀態下，按照+202/95%（+2%/-3%）濕度放置2h；-203放置30min；轉換時間40min設置進行試驗，共連續進行5個循環；試驗結束后立即進行測試。The samples idle, Do the test as the temperture is 202 and the humidity is 95%（+2%/-3%） for 2h; then the temperture is -203 for 30minutes, conversion time in 40minu5PCS通過基本功能、性能測試；外觀和結構正常Base function and performance test is OK; Appearance and structure are normal.9污物混入實驗Filth interfuse test驗證手機結構密閉性.Validate the frame obturation of the handset.將電池裝在手機上，關機狀態下放入裝有300目滑石粉的袋子中，上下振蕩200次，左右振蕩200次，前后振蕩200次，共計600次。完成后取出觀察主屏、副屏進塵程度。put the power off and with battery samples in the bag with talcuum powder 300 mesh, surge up and down 200 times, surge around 200 times, surge front and back 200 times, 605PCS污物不得進入LCD內，手機功能正常。LCD havent any filth. The function is normal.10極限溫度充電實驗Limit temperature Charge Test驗證手機在極限溫度條件下的充電性能Validate the performance of the handset to charge under the limit temperature condition.分別在-53及+452溫度下，在手機達到環境溫度并且穩定后充電30分鐘，電池電壓能夠上升。Under the temperture -53 and +452, Alternate charge the handset for 30minutes, the battery voltage must rise.5PCS手機充電指示正常（即充電指示燈點亮，充電圖標跑動）；在手機達到環境溫度并且穩定后充電30分鐘，電池電壓能夠上升。The charge is show normal(the charge LED is light, charge ico is running); The battery voltage has risen after chargeing 30 minutes.11鹽霧實驗Salt mist test驗證手機產品抗鹽霧腐蝕的能力 Validate the resistance of the handset in the salt mist.溶液含量為5%的氯化鈉溶液。將手機關機放在鹽霧試驗箱內(箱內溫濕度分別為+352，90%（+2%/-3%）RH)，樣機.豎直放置24h、正面放置10h、反面面放置10h，以免溶液噴灑不均或有的表面噴不到，樣機需立即被放入測試箱。實驗期滿。取出樣機，清水擦拭后烘干，進行試驗后檢查。put 5% NaCI liquor into the tester. put the power off samples in the salt mist test box(the room temperture is +3PCS通過基本功能、性能及外觀測試Base function, performance and appearance test is ok.12隨機振動Random Vibration Test驗證手機經受規定嚴酷等級的隨機振動的能力Validate the performance of the handset under asperity vibration athletics.被測樣機不包裝、處于通電待機狀態。牢固固定在試驗臺上。試驗參數：+6dB/oct，頻率范圍10-20Hz ；頻率范圍20-500Hz，功率頻譜密度0.05 g2/Hz。軸向：三個軸向。持續時間：每方向1小時，共3小時。持續時間結束，取出被測樣機進行試驗后檢查。Fixup the unpacked and power on samples on the test table. Test parameter: +6dB/oct，frequency is from 5 to 20Hz and from 203PCS通過基本功能、性能及外觀測試Base function, performance and appearance test is ok.13正弦振動Sinusoidal vibration test模擬手機在運輸過程中產生的振動。Simulate the transport vibration, and validate the handsets reliabilty.樣機不包裝、處于插卡通電待機狀態，在振幅1.5mm，頻率范圍5-10Hz ；在加速度為3g，頻率范圍10-200Hz ；以1 oct/mn掃頻速度進行X、Y、Z三個方向，每個方面各振動1小時，共3個小時，試驗結束后進行試驗后檢測；The samples in unpacked and power on with SIM card. Frequency from 5 to 10Hz, swing is 1.5mm; Frequency from 10 to 200Hz, acceleration is5PCS通過基本功能、性能及外觀測試Base function, performance and appearance test is ok.14包裝振動packaging vibration endurance Test檢驗手機包裝材料對手機產品的保護作用及手機結構配合、機殼材料的耐磨性、部件焊接質量等Validate the protect ability from the wrapper, structure inosculate of the product, wearability of the shell material and solder quality of the components etc.被測樣機包裝好放于試驗臺上。試驗參數：頻率5-200Hz ，振幅15-20mm，在X、Y、X三個正弦方向各振動1小時，共3小時。持續時間結束，取出被測樣機進行試驗后檢查。put the packed samples on the test table. Test parameter：Frequency from 5 to 200Hz, swing from15 to 20mm, every axis vibrate for 1h, sum up 3h. Duration over,take out an1箱1box樣機及手機配件通過基本功能、性能及外觀測試；The handset and fittings can pass base function,performance and appearance.15包裝跌落packaging drop endurance Test檢驗手機包裝材料對手機及附件的年外觀、功能等的保護作用Validate the protect ability of the appearance and function from the wrapper.以包裝出貨的整箱手機按一角三邊六面各跌一次，試驗后結樣機及配件進行全檢。跌落標準如下：當產品毛重G10kg時，進行1M高度跌落；當產品毛重10kgG20kg時，進行80CM高度跌落；當產品毛重G20kg時，則進行60CM高度跌落；The handset packed with case waiting for shipment, drop 1 time of 1 angle, 3 edges, 6 faces. Final check of the samples and fittings1箱1box樣機及手機配件通過基本功能、性能及外觀測試；允許不多于2個（含2個）的內部包裝破裂、損傷。The handset and fittings can pass base function,performance and appearance; Allow the inner packing and destroy crack 2 boxes at the most.161M跌落實驗1M drop test驗證手機及電池抗多次跌落于地上的能力Validate the capacity of the handsets and battery to resist being dropped repeatedly onto concrete.被測樣機不包裝、處于插卡通電待機狀態。從1m高度（屏幕小于2.4,或不超過屏本身所在面積的40%)，初速度為0并自由跌落于光滑混凝土地面上，6個面、4條邊，每面跌落2次,每條邊跌1次，共計16次。每4次對樣機外觀、功能進行全檢，試驗結束，對樣機進行全面檢查。配套電池跌落：6個面、上方左右2條邊各跌一次，共計8次，每2次對進行檢查，試驗結束，對電池進行全面檢查。The samples unpacked and power on with SIM card, then drop from 1 mete10PCS通過基本功能測試、性能測試，未有明顯的裂紋/破損，內部未見零件松動及異常pass base function, performance test: No obviously crack / damage, no inner-components loose or