In Cell觸摸屏原理-文檔資料

1、1In-Cell觸摸屏原理2010.3.152Introduction of touch panel 1. Resistive touch panel 1.1 traditional resistive touch panel (directly glue on LCD module) a. 4/5/6/8-wire resistive touch panel b. digital resistive touch panel (touch switches, matrix) 1.2 integrate resistive touch panel into LCD cell (between t

2、op and bottom glasses) 2. Capacitive touch panel 2.1 capacitance changed by deformation of top glass 2.2 capacitance changed by induced current from finger 2.2.1 surface capacitive touch panel 2.2.2 projective capacitive touch panel2.2.2.1 detect self capacitance2.2.2.2 detect mutual capacitance 3.

3、Other touch panel (Infrared, SAW, Electromagnetic, Optical) 3Resistive touch panel基本原理：觸摸時，兩層ITO互相接觸，從而在兩層ITO之間形成電阻通路根據上下基板材料，可分為film on glass, glass on glass, film on film等結構。41.1 4-wire resistive touch panel在兩電極上加5V直流電在ITO均勻電阻平面上形成均勻穩恒電流場在另一面的ITO電極上測量電壓根據測得電壓值（0-5V）確定觸摸點的位置用同樣方法測量Y坐標51.1 4-wire re

4、sistive touch panelLow life time (around 1 million times)Low transmissivity (75%-85%)Not resist scratchLowest costEasy detect circuitWorks with any stylus61.2 Incell resistive touch panelsamsung(1)Basic principle:When pressed, the sensor switch is on (conductive column spacer contact sensor electrod

5、e)From plan view, at touch point, common electrode contact two sensing lines perpendicular with each other respectively7 2. Capacitive touch panel 2.1 capacitance changed by deformation of top glass 2.2 capacitance changed by induced current from finger 2.2.1 surface capacitive touch panel 2.2.2 pro

6、jective capacitive touch panel2.2.2.1 detect self capacitance2.2.2.2 detect mutual capacitance82.1 Capacitive touch panel (壓力式壓力式)This integrate type has some different structures, includes:Cell gap change typeSamsung filed a patent (US20080048994). AUO has made a demo.LC alignment change typeSamsun

7、g filed patent (US20050094038) very early, but Samsungs demo applied another detect circuit (SID07 24.3), and Epson made a demo (SID08 55.2) based on Samsungs structure by using LTPS, IPS and active matrix sensor so that improved the performance.9Cell gap change type(1)Samsungs patent (US20080048994

8、) only posed a basic principle, its layer structure and detailed detect method is not shown in the patent.Though AUO has made a demo, there are very few open materials of its detect principle.They use the same principle: detect the capacitance change between common electrode and sense electrode by c

9、ell gap deformation.There are many ways to detect capacitance change, which way Samsung and AUO used is unknown.AUOSamsung10Cell gap change type(2)AUO和和LG的壓力式內嵌觸摸屏樣品的壓力式內嵌觸摸屏樣品11LC alignment change typeSamsung(1) Samsungs patent (US20050094038) first proposed this method: Because different LC alignm

10、ent has different dielectric constant, and when pressed, the LC alignment is changed, so that the LC capacitance changed.12LC alignment change typeSamsung(2)Samsung和Epson的in-cell LC alignment change type TPSamsungEpson132.2.1 Surface capacitive touch panel Have 2 conductive coatings. Upper conductiv

11、e coating is the working plane. Lower coating is shielding plane.14Surface capacitive touch panelSurface capacitive touch panel principle: Touch point is treated as connecting to ground by a capacitor. The resistor from touch point to 4 corners R1-4 is related to the distance from touch point to 4 c

12、orners. The more the distance is, the more the resistor is.When add sine signal on 4 corners, the current at 4 corners I1-4 is inverse proportion to related R1-4. By measuring I1-4, the touch point can be detected.15Surface capacitive touch panelLong life time (around 100 million times)Higher transm

13、issivity (Can reach 90%)Only work with fingersHigher costPatent issueComplex detect circuitFast response speed162.2.2投射電容觸摸屏投射電容觸摸屏(PCT)投射電容觸摸屏（projective capacitive touch panel）可分為兩種不同的結構：自電容(self capacitive)與互電容(mutual capacitive)自電容為較早的技術，來源于touch key, touchpad互電容技術由iphone發揚光大，發展迅猛，將逐漸取代自電容類型17Se

14、lf capacitance自電容原理為當手接觸時，等效為parasitic capacitance增加，而且自電容檢測都是在前端（提供電源端）。檢測原理有很多，可檢測電壓、電流、電荷，下圖為charge transfer檢測原理。通過開關依次開合不斷對parasitic capacitance進行充電放電，檢測放電時通過的電荷，當有手指接觸時，流出電荷增加。18Detect self capacitancePanel layout: generally using diamond pattern, so the capacitor from finger to both ITO layers

15、 will be big enough. The detect sequence is, first detect self capacitance at one layer (red), one line by one line, to get X position, then detect another layer (blue), to get Y position. So this is fake multi-touch.19Projective capacitive touch panel自電容的多點觸摸定位問題：自電容的多點觸摸定位問題：20Mutual capacitance互電

16、容原理為：當手指接觸時，等效為互電容改變，互電容檢測一般是在后端（sense端）?？梢詸z測電壓或者電荷。下圖為電荷檢測等效電路。手指接觸后等效為互電容減小，此時讀出電荷減小。模型一21Mutual capacitancePanel 圖案圖案22Mutual capacitanceDriving method: At drive layer (red), add pulse signal one line by one line, and other lines connect to ground. At sense layer (blue), detect charge one by one.

17、 When all intersection is detected, the most charge decreased intersection is the touch point.This method is true multi-touch. So apple claimed that iphone is the first image sensing touch panel in the world.上表面和下表面diamond是錯開的23模型仿真結果No touchTouch24互電容的優點互電容的優點互電容相對自電容的顯著優點：對地寄生電容對觸控檢測影響很小，更適合在集成觸摸屏

18、結構具有更強的抵抗LCD噪聲能力可以實現真正的多點觸摸（不會有鬼點）但互電容是一個更加新的技術，目前幾乎所有觸控IC廠商采用的感應技術都不一樣，各自研發自己的觸控技術。25Other touch technology紅外：透光度好，價格低，適應惡劣環境缺點：分辨率較低，易損壞在屏幕四邊排布紅外發射管和紅外接收管，一一對應形成橫豎交叉的紅外線矩陣。用戶在觸摸屏幕時，手指就會擋住經過該位置的橫豎兩條紅外線，因而可以判斷出觸摸點在屏幕的位置。 26Other touch technology聲表面波：透光好，壽命長缺點：易被油污，灰塵等影響，需經常維護X 軸發射器X 軸接收器反射陣列可觸摸區域吸收殘波膠帶Y 軸接收器Y 軸發射器當手指或