dsp實驗：定時器

1、實驗三：定時器1、 實驗原理1.定時器的結構2. 定時器中斷周期3.實驗功能：通過XF管腳控制LED閃動以一定規律進行閃爍。2、 硬件資源及在片外圍電路硬件資源： DSP芯片、CPU、LED、蜂鳴器、電阻、電容等在片外圍電路： 時鐘發生器、定時器、通用輸入/輸出口等3、 參數設置CPU工作時鐘： *clkmd =0x21b3; 0010000110110011 CLKOUT=18M中斷頻率： 9 /* PRSC 4bit*/ 18M/9000=2KHZ4、 實驗流程圖5、 程序#include <stdio.h>#include <csl.h>#include <

2、csl_irq.h>#include <csl_timer.h>#include <csl_chiphal.h>extern void VECSTART(void);#define TIMER_CTRL TIMER_TCR_RMK( TIMER_TCR_IDLEEN_DEFAULT, /* IDLEEN = 0 */ TIMER_TCR_FUNC_OF(0), /* FUNC = 0 */ TIMER_TCR_TLB_RESET, /* TLB = 1 */ TIMER_TCR_SOFT_BRKPTNOW, /* SOFT = 0 */ TIMER_TCR_FRE

3、E_WITHSOFT, /* FREE = 0 */ TIMER_TCR_PWID_OF(0), /* PWID = 0 */ TIMER_TCR_ARB_RESET, /* ARB = 1 */ TIMER_TCR_TSS_START, /* TSS = 0 */ TIMER_TCR_CP_PULSE, /* CP = 0 */ TIMER_TCR_POLAR_LOW, /* POLAR = 0 */ TIMER_TCR_DATOUT_0 /* DATOUT = 0 */ ) /* Create a TIMER configuration structure that can be pass

4、ed */* to TIMER_config CSL function for initialization of Timer */* control registers. */TIMER_Config timCfg0 = TIMER_CTRL, /* TCR0 */ 0x3400u, /* PRD0 0x3400=13312*/ 14400, /* PRD0 16bit 0x3400=144000=14400*10*/ 9 /* PRSC 4bit*/;/中斷頻率=Fcpu/(9000*1)=144MHz/13312=1kHzUint16 eventId0; /* Create a TIME

5、R_Handle object for use with TIMER_open */TIMER_Handle mhTimer0;volatile Uint16 timer0_cnt = 0;/* Function/ISR prototypes */interrupt void timer0Isr(void);int old_intm;Uint16 tim_val;Uint16 xfchange = 0;Uint16 ms,f;void main(void) /* Initialize CSL library - This is REQUIRED ! */ /*CLS庫的初始化，這是必需的*/

6、CSL_init(); /* Set IVPH/IVPD to start of interrupt vector table */ /*修改寄存器IVPH，IVPD，重新定義中斷向量表*/ IRQ_setVecs(Uint32)(&VECSTART); /* Temporarily disable all maskable interrupts */*禁止所有可屏蔽的中斷源*/old_intm = IRQ_globalDisable(); /* Open Timer 0, set registers to power on defaults */*打開定時器0，設置其為上電的的默認值

7、，并返回其句柄*/mhTimer0 = TIMER_open(TIMER_DEV0, TIMER_OPEN_RESET);/* Get Event Id associated with Timer 0, for use with */* CSL interrupt enable functions. */*獲取定時器0的中斷ID號*/ eventId0 = TIMER_getEventId(mhTimer0);/* Clear any pending Timer interrupts */*清除定時器0的中斷狀態位*/IRQ_clear(eventId0);/* Place interrupt

8、 service routine address at */* associated vector location */*為定時器0設置中斷服務程序*/IRQ_plug(eventId0,&timer0Isr);/* Write configuration structure values to Timer control regs */*設置定時器0的控制與周期寄存器*/ TIMER_config(mhTimer0, &timCfg0); /* Enable Timer interrupt */*使能定時器的中斷*/IRQ_enable(eventId0); /* Enab

9、le all maskable interrupts */*設置寄存器ST1的INTM位，使能所有的中斷*/IRQ_globalEnable(); /* Start Timer */*啟動定時器0*/TIMER_start(mhTimer0);ms=0;for(;)/ Wait for at least 10 timer periods /等待10個定時周期if(xfchange = 0) /點亮XF的LED CHIP_FSET(ST1_55,XF,1); else/關掉XF的LED CHIP_FSET(ST1_55,XF,0); /* Restore old value of INTM */*恢復INTM舊的值*/IRQ_globalRestore(old_intm);/* We are through with timer, so close it */*關掉定時器0*/TIMER_close(mhTimer0); /