PHP實現連接設備、通訊和發送命令的方法

1、本文實例講述了PHP實現連接設備、通訊和發送命令的方法。分享給大家供大家參考。具體如下：開發的BS架構的軟件（PHP），需要跟設備進行通訊，在此記錄一下，歡迎各位指正：1. 采用php socket技術使用TCP/IP連接設備參數$service_port 連接端口參數$address 發送IP地址參數$in 發送命令?123456789101112131415161718192021222324252627282930function Send_socket_connect($service_port, $address, $in) /創建 TCP/IP socket$socket = so

2、cket_create(AF_INET, SOCK_STREAM, SOL_TCP) or die("could not create socket!");/設置超時時間$timeout = 2;$time = time();/設置非阻塞模式socket_set_nonblock($socket);/超時判斷while (!socket_connect($socket, $address, $service_port) $err = socket_last_error($socket);/ 連接成功，跳出循環if ($err = 10056) break;/連接失敗，判斷超

3、時時間，停止if (time() - $time) >= $timeout) socket_close($socket);print('網絡異常，請檢查網絡連接！');exit();/ 刷新頻率（250毫秒）usleep(250000);/設置阻塞模式socket_set_block($socket);/發送命令到設備socket_write($socket, $in, strlen($in);/關閉連接socket_close($socket);Send_socker_xdcoder $buffer為返回值?1234567891011121314151617181920

4、212223242526272829303132333435function Send_socket_xdcoder($service_port, $address, $in) /創建 TCP/IP socket$socket = socket_create(AF_INET, SOCK_STREAM, SOL_TCP) or die("could not create socket!");/設置超時時間$timeout = 2;$time = time();/設置非阻塞模式socket_set_nonblock($socket);/超時判斷while (!socket_co

5、nnect($socket, $address, $service_port) $err = socket_last_error($socket);/ 連接成功if ($err = 10056) break;/連接失敗，判斷超時時間，停止if (time() - $time) >= $timeout) socket_close($socket);echo "<script>alert('網絡異常，請檢查網絡連接！');</script>"exit();/ 刷新頻率（250毫秒）usleep(250000);/設置阻塞模式sock

6、et_set_block($socket);/發送命令到設備socket_write($socket, $in, strlen($in);/接收設備命令返回數據$buffer = socket_read($socket, 1024, PHP_NORMAL_READ);/關閉連接socket_close($socket);/輸出返回值return $buffer;2. 采用php socket技術使用UDP協議連接設備，實現通訊和發送命令參數$service_port 連接端口參數$address 發送IP地址參數$in 發送命令?123456789101112function Send_soc

7、ket_connect_udp($service_port, $address, $in) /采用php socket技術使用UDP協議連接設備$socket = socket_create(AF_INET, SOCK_DGRAM, SOL_UDP);socket_set_option($socket, SOL_SOCKET, SO_RCVTIMEO, array("sec" => 2, "usec" => 0);/發送命令socket_sendto($socket, $in, strlen($in), 0, $address, $servi

8、ce_port);socket_recvfrom($socket, $buffer, 1024, MSG_WAITALL, $address, $service_port);/關閉連接if (empty($buffer) echo "<script>alert('網絡異常，請檢查網絡連接！');</script>"Send_socket_xdcoder_udp $buffer 為返回值?123456789101112131415function Send_socket_xdcoder_udp($service_port, $addre

9、ss, $in) /采用php socket技術使用UDP協議連接設備$socket = socket_create(AF_INET, SOCK_DGRAM, SOL_UDP);socket_set_option($socket, SOL_SOCKET, SO_RCVTIMEO, array("sec" => 2, "usec" => 0);/發送命令socket_sendto($socket, $in, strlen($in), 0, $address, $service_port);socket_recvfrom($socket, $bu

10、ffer, 1024, MSG_WAITALL, $address, $service_port);/關閉連接socket_close($socket);if (!empty($buffer) return $buffer; else echo "<script>alert('網絡異常，請檢查網絡連接！');</script>"3. 采用RS232串口技術連接設備，實現通訊和發送命令參數$com 串口號參數$baudratr 波特率參數$in 發送命令?1234567891011121314151617function rs232_c

11、onnect($com, $baudrate, $in) set_time_limit(10);/使用 'windows下設置竄口參數'exec("mode " . $com . " BAUD=" . $baudrate . " PARITY=n DATA=8 STOP=1 odsr=off");/ "打開端口串口$com"$f = fopen($com, 'w+');/判斷串口是否正常打開if (!$f) /echo "<script>alert('Error when open $com！');</script>"die("Error when open $com");/向串口發送數據;fwrite($f, $in);/關閉端口 fclose($f);/串口操作結束還有一個關于命令16進制轉